上海妙定電氣有限公司 全國咨詢熱線：
PRODUCT CLASSIFICATION
產品分類
更新時間：2019-09-16 
瀏覽次數：1531電能質量分析儀配有一條四芯的電壓測試線、一套電流測試線和三只電流測試鉗(根據需要可配備到六只).電壓測試線用來接入被測電壓信號,通常在現場要求精度不是很高時用電流鉗進行測試,每只電流鉗分別對應一個鉗表接口,不能互換,否則會影響測試精度,每只鉗表中間有一個圓標貼,顯示出鉗表的相別和極性(標N的一端為電流的流出端,在使用接線要注意極性,接反會影響測試結果).
在測試過程中要注意的問題:
1.要在測試前插好電流測試鉗,嚴禁先夾被測信號后插入電流鉗插座,這相當于電流測試鉗二次開路,容易產生開路高壓,損壞儀器.測試完成后要先摘下所有電流測試鉗再拔下與主機相連的插頭.
2.測試鉗為保證各通道精度,應一一對應,要把各電流鉗正確插入wei一與之對應的插座.交換不同輸入,會降低了測試精度,但交叉后一般測試精度也不會超出在±2%.
3.接入電壓信號時測試線一定要先接到儀器的電壓端子,然后再接到被測設備的電壓端子;測試完成后一定要先摘下被測設備的電壓接頭,然后再拆除儀器側的電壓線.(此條尤為重要,反之可能引起大事故)
您的位置：
